Stuart-turner Techflo TP 60TNH Manual do Utilizador

Installation, Operation & Maintenance InstructionsPlease leave this instruction booklet with the home owner as it contains important guarantee, ma

- 10 -Cont ...3.12 Hose to pump: The pump inlet and outlet ports have fittings which are specifically designed for connection to the G ¾ femal

- 11 -Cont ... 2. Prior to inserting pipe into fitting, mark the insert depth on the wall of the pipe with a soft pencil at a distance of 31 m

- 12 -Cont ...If you have any concern either about using push-in fittings or should the joint leak on final test, isolate the water supplies and conta

- 13 -Cont ...4 ELECTRICAL INSTALLATION4.11 Regulations: The electrical installation must be carried out in accordance with the current natio

- 14 -Cont ... The wire which is coloured green and yellow must be connected to the terminal in the connection unit which is marked with the lett

- 15 -Cont ...4.24 Cable Gland Fitting Instructions: To enable correct assembly of the cable gland the ‘O’-ring (Fig. 16 item 1) must be placed

- 16 -Cont ...5 COMMISSIONING5.11 System Flushing: This pump incorporates push-in connectors and plastic components that must not come into cont

- 17 -Cont ...6 MAINTENANCE6.11 Isolate the unit from the electrical supply before commencing any work. 6.12 Turn off water supplies to the pump a

- 18 -Cont ...6.14 Water scale: As water is heated scale deposits are released in areas of hard water, scale can cause the mechanical seal to

- 19 -Cont ...Techflow Products reserve the right to amend the specification in line with its policy of continuous development of its products.Note:

- 2 -PRODUCT DESCRIPTIONElectric motor driven single or twin ended peripheral pumps complete with an automatic control system, consisting of flow swit

- 20 -8 TROUBLE SHOOTING GUIDESymptoms Probable Cause Recommended ActionPump will not start. Electrical supply. Check power supply.Check fuse (see fu

- 21 -Cont ...8.11 Dry Run Protection: This pump is fitted with a PCB that will detect the following fault conditions:  Dry running caused by wat

- 22 -Cont ... IMPORTANT – Ensure there is no contact with any of the internal parts of the terminal box.  Briefly reconnect the mains power su

- 23 -Cont ...8.14 Flow Switch Circuit Test: 1. First confirm visually that the flow switch reed clamps have not been dislodged during handl

- 24 -9 THE TECHFLOW GUARANTEECongratulations on purchasing a Techflow pump. We are confident this pump will provide many years of trouble free servi

- 25 -NOTES

- 26 -NOTES

- 27 -NOTES

Techfl ow Products, Service Department, Greys Road, Henley-on-Thames, Oxfordshire RG9 1RY ENGLAND Tel: +44 (0) 1444 258017, Fax: +44 (0) 1444

- 3 -Your product may vary slightly from the picture above.PRE-INSTALLATION CHECKThe pressure vessel is supplied as a separate item, and will need to

- 4 -1 READ BEFORE COMMENCING PUMP INSTALLATIONA. Water storage capacity.1.11 The hot and cold water storage capacity must be sufficient to meet th

- 5 -Cont ...2 LOCATION - GENERAL2.11 Access: For emergencies and maintenance the pump must be easily accessible.2.12 Protection: The pump must

- 6 -Cont ...2 LOCATION - SINGLE PUMPCold water connection:2.27 The cold water supply: The supply must be AIR FREE and have a DEDICATED CONN

- 7 -Cont ...Hot water connection:2.28 Hot water cylinder or storage tank: When a hot water cylinder or storage tank is used, ensure the pipewor

- 8 -Cont ...2.32 Non-preferred pump location: If it is not possible to locate the pump in the preferred area due to site limitations and it is

- 9 -Cont ...3 PUMP CONNECTIONS  Do not use stainless steel, chrome or nickel plated pipe with the flexible hose push-in plumbing connections.